NewBeeDrone BeeID v1.1 M10Q GPS Module with RemoteID

Remote ID. GPS Accuracy. Drone Recovery. All-in-One.

The NewBeeDrone BeeID v1.1 is a compact GPS module that integrates FAA Remote ID capability with a built-in Bluetooth beacon. While Remote ID is a requirement for flying in the US, the BeeID remains a versatile tool elsewhere, offering both GPS and tracking functions.

At its core it uses an M10 GPS chip, making it fully compatible with Betaflight’s GPS Rescue mode, iNav, and Ardupilot. Beyond navigation, it provides an added safety net as a locator if your drone goes down. The module can supply the last known GPS coordinates via your radio’s telemetry, or allow you to track the quad in real time using Bluetooth and a smartphone app. In open conditions, Bluetooth reception has been shown to exceed 150 m, and once you get closer, it can guide you directly to the aircraft.

Compact, lightweight, and multi-purpose, the BeeID combines modern compliance with practical recovery features to give peace of mind in the air.

Built-In Drone Tracker for Easier Drone Recovery

The NewBeeDrone BeeID v1.1 M10Q GPS Module with RemoteID & Drone Tracker goes beyond compliance. Its integrated Drone Tracker helps you locate and recover your downed drone using apps like Drone Scanner — no extra hardware needed.

• Built-in Drone Tracker using BLE signal
• Supports smartphone-based search apps
• Designed for long-range and freestyle recovery situations
• Improves your chances of successful drone recovery

High-Performance GPS You Can Rely On

With the advanced u-blox M10Q chipset and a high-gain ceramic antenna, the BeeID module locks satellites fast and delivers stable, accurate positioning — perfect for GPS Rescue and autonomous navigation.

• Supports GPS / GLONASS / GALILEO
• 72-channel parallel tracking
• Fast lock times and accurate coordinates
• Works with Betaflight, iNAV, Ardupilot, PX4.

Remote ID Built In — When You Need It

Flying drones over 250g in FAA-regulated airspace? The BeeID v1.1 M10Q includes fully compliant Remote ID broadcast functionality. It activates when required and stays in the background when not. Remote ID is included for compliance, without interfering with GPS or Drone Tracker functions.

Features:

• High-precision u-blox M10Q GPS
• Built-in Drone Tracker for signal-based drone recovery
• Remote ID compliant for FAA requirements
• Lightweight and compact (approx. 5.2g)
• Ceramic GPS antenna for strong reception
• WiFi setup via phone or PC
• Standard UART interface
• Built-in barometer for Remote ID altitude broadcasting

Please note: BeeID does not have a compass module.

Why Choose BeeID v1.1 M10Q?

Because modern flying demands more than just compliance — it demands reliability. With fast GPS lock, a built-in Drone Tracker, and fully integrated Remote ID, the BeeID v1.1 M10Q helps you navigate confidently and recover faster when things go wrong.

Whether you’re flying freestyle, long-range, or commercial missions — this module has your back.

• BeeID 3D File 

BeeID M10Q – GPS + Bluetooth  Setup Instructions

Step 1: Verify Flight Controller Compatibility

Before installation, ensure that your flight controller (FC) and its firmware support the UBLOX GPS protocol.

• Some older versions of Betaflight firmware may not be compatible with UBLOX GPS.

• It is recommended to update your FC to the latest firmware to ensure proper functionality.

Step 2: Wiring the BeeID M10Q GPS Module

Proper wiring is essential for accurate data transmission between the BeeID module and your flight controller. Follow these steps:

• Connect the BeeID TX (Transmit) pin to the FC RX (Receive) pin on the same UART port.

• Connect the BeeID RX (Receive) pin to the FC TX (Transmit) pin on the same UART port.

• Ensure 5V power and ground are correctly connected to provide stable operation.

Step 3: Configuring the UART Port

After wiring, configure the corresponding UART port in your flight controller firmware:

• Set the baud rate to 115200bps to match the module’s default speed.

• Enable GPS mode on the selected UART port.

• Save and reboot your flight controller to apply the changes.

Step 4: Confirm GPS Functionality

• Verify that the module successfully acquires GPS satellites.

• In Betaflight, iNAV, or Ardupilot, check the GPS status page for satellite lock and position updates.

• Ensure that RemoteID broadcasting is active and functional via BLE. You can use the Drone Scanner App to check the broadcasting information.

⚠️ IMPORTANT for iNAV Users
Please disable the AUTO-CONFIG setting in iNAV to ensure proper functionality of the BeeID module.