FlyingTech.co.uk Site Logo

 

 

Specialist in Multirotor Tech & FPV Equipment


COVID-19 Update: Flying Tech is open and operating as usual - shipping daily. Please note shipment times may take longer than normal as postal services are operating with fewer staff. Thanks to all of our customers for their support and stay safe.

VIDEO TRANSMITTER 5.8G VTX-MINI

Title

Matek Mini VTX 5.8Ghz Video Transmitter 25 - 800mW

£24.90
VIDEO TRANSMITTER 5.8G VTX-MINI 40CH, PIT/25/200/400/500mw switchable, 6~30V Input, Button+LED control, BFCMS control, PINIO Power Switch, Microphone, 20-30mm Mount. The Matek Mini VTX may be small, but it doesn't leave anything out. It packs in a massive 800mW power output, which is switchable starting from 25mW and 40 channels across bands A/B/E/F/R. There's also features like pit mode, betaflight control via the Tramp Protocol and it has an onboard microphone and 5V BEC to power a camera. The VTX suits 20mm hole mounts but it also comes with a 30.5mm extension board, making it compatible with quads of all sizes. The antenna connection is MMCX.
Brand: 
Matek Optical Flow & Lidar Sensor 3901-L0X

Matek Optical Flow & Lidar Sensor 3901-L0X

£21.90

This sensor works the same way as an optical mouse, helping your iNAV quad maintain position without GPS! It has a working range of up to 2m, and uses a VL53L0X Lidar rangefinder along with a PMW3901 optic flow module. The sensor is connected to your flight controller via a UART and is currently only supported by INAV - other firmware projects like betaflight will support this sensor in the future.

Tips:

Collection: 
Brand: 
Matek 1G3 VRX

Title

Matek 1G3 VRX Long Range 1.2GHz - 1.3GHz Video Receiver

£42.50
This is a 9CH 1.2GHz - 1.3GHz Long Range Video Receiver from Matek. It's designed to match their 1G3 Video Transmitter. The neat thing about this video receiver is that it fits a Fat Shark module bay, so you can install it in compatible FPV goggles or ground station docks. The module comes complete with a PCB antenna. FrSky R9 / TBS Crossfire Users - these radio control systems can interference with the Matek 1G3 video link as they operate on adjoining frequencies. To help reduce interference we recommend fitting a notch filter or using a 5.8Ghz relay station so that the 1G3 VRX can be positioned away from your radio control. Settings Press and hold the button 2 seconds to enter the frequency setting. Frequency LED blinks Press the button to select the frequency When the LED blinks at new frequency, no RF input is enabled on this frequency New frequency will be saved if no button action within 3 seconds
Brand: 
Category: 
Matek 1G3 Long Range 1.2GHz - 1.3GHz 600mw Transmitter

Title

Matek 1G3 Long Range 1.2GHz - 1.3GHz 600mw Transmitter

£37.99
This video transmitter from Matek is designed for super long range FPV. It operates on 1.2-1.3Ghz, which provides much better signal penetration through obstacles and long-range reception than 5.8Ghz. The VTX has a fixed 600mW power output and a single band with 9 channels. A compatible Matek video receiver for the 1G3-VTX is sold here. IMPORTANT: The use and operation of this product in your country may require an amateur radio license, and some countries may forbid its use entirely (It is NOT Legal in the UK). It is the responsibility of the purchaser to ensure that the purchase and use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Flying Tech Ltd cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. FrSky R9 / TBS Crossfire Users - these radio control systems can interference with the Matek 1G3 video link as they operate on adjoining frequencies. To help reduce interference we recommend fitting a notch filter or using a 5.8Ghz relay station so that the 1G3 VRX can be positioned away from your radio control. Settings Press and hold the button 2 seconds to enter the frequency setting. Frequency LED blinks Press the button to select the frequency When the LED blinks at new frequency, no RF output on this frequency New frequency and output will be enabled if no button action within 3 seconds *** CMS control is not supported for now *** This is the International 9HC Version. The 2CH US version is locked to 1258 & 1280MHz and cannot be unlocked to 9CH.
Brand: 
Category: 

Pages

Subscribe to RSS - Mateksys