FlyingTech.co.uk Site Logo

 

 

Specialist in Multirotor Tech & FPV Equipment

Diatone Motor ESC “RaceWire” PCB 30mm / 35mm / 40mm

Diatone Motor ESC “RaceWire” PCB 30mm / 35mm / 40mm

£1.90
Make your build look neat and tidy with RaceWire from Diatone. RaceWire replaces the wire between you 4-in-1 ESC and motor with what's essentially a PCB. The advantage being it not only looks neater, it protects against prop strikes catching your motor wires and also makes it much faster to replace a motor. The PCB is of a fixed length, so they come as a set of 3 boards including three sizes to match your build:  30mm, 35mm and 40mm. You will need to order four sets for a quadcopter build. When mounting the RaceWire to your carbon fibre frame please make sure that the PDB is insulated from the carbon fibre to avoid any possibly short circuits - we recommend using this double-sided adhesive foam mounting tape. Advantages of using RaceWire: It can be used as extension in case your motor wires aren’t long enough Easier to change motors because you don’t need to get into the FC/ESC stack It prevents damage from prop strikes that could cut your motor wires
Brand: 
Category: 
Collection: 
Diatone Circular Flash Bang Motor Mount 2812 RGB LED Board -  SW522/AN

Diatone Circular Flash Bang Motor Mount 2812 LED Board

£2.90

This programmable LED board from Diatone is designed to attach beneath a motor on your racing drone. It has M3 hole cut outs that will suit 18XX / 22XX sized motors, typically anything used by a 5" racing quad. As the board features addressable 5 volt 2812 LEDs, you can programmed it via BetaFlight / Cleanflight to do lots of interesting things like flashing colour patterns to reflect arming status, flight modes, braking, battery status and so on. Alternatively if you prefer a solid colour you can set it up to do that too.

Collection: 
Category: 
Brand: 
Diatone SW604 Flash Bang 2812 RGB Programmable LED Board

Diatone Flash Bang 2812 RGB Programmable LED Boards

£6.90

Here we have Diatone's Flash Bang Series of 2812 Addressable LED Boards which are perfect to fit to the rear of your racing quad. There are available in a variety of sizes to suit different applications. All of the variants use 2812 5volt RGB LEDs which can be programmed via BetaFlight / Cleanflight. If you just want to keep it simple you can assign a solid colour. Alternatively you can do lots of interesting things like programming flashing colour patterns to reflect arming status, flight modes, braking, battery status and so on.

Collection: 
Category: 
Brand: 
Diatone 3-4S LED Light Board Set White, Red, Green & Blue

Diatone 3-4S LED Light Board Set White, Red, Green & Blue

£6.00

Here we have a set of LED light boards that are ideal for racing drones. They are the perfect size for mounting onto the arms of your race quad and they are really bright too. 

The light boards are very simple to use. There’s no programming involved so all you need to do is provide power, they are compatible with 3S(11.1V) / 4S(14.8V). They come as a set of four, including a board of each colour: White, Red, Green and Blue. The light boards come as a single PCB, but they can be broken apart if you want to mount them individually.

Collection: 
Category: 
Brand: 
Diatone Universal Mini Camera Lens Adjustable Tilt Mount

Title

Diatone Universal Mini Camera Lens Adjustable Tilt Mount

£3.90
This mount is designed to fit tiny FPV cameras like our  700TVL 1/4 CMOS camera. The mount can be adjusted for the best angle while flying FPV. The mount is available in four colour options, Black, Blue, Orange and Green – please select as required. All come with fixings screws.
Brand: 
G5" Propeller Guard Pack

Glass Fibre 5" Propeller Guard Pack For 210 - 250 Quadcopter

£4.50
Tired of breaking your props? Worried about crashing into things and damaging them? We have the answer.  These prop guards are perfect for most small quadcopters and are simple to install. At just 1mm thick, they mount directly under the frame using the same screws that go on to attach your motors. They measure 2.95" from the center of the motor mount position to the edge of the protector, making these suitable for 5" props. You could use them with 6" props too, but a small amount of prop may stick out.
Brand: 
Category: 
Diatone XT30 with Integrated Current Sensor Module

Diatone XT30 with Integrated Current Sensor Module (30/50A)

£3.95
A new innovative product from Diatone, that will take away the guessing on how much flighttime is left in your battery. This XT30 connector has an integrated current sensor that makes it very easy to measure how many mAh you have used during flight. Measuring current draw is a much more reliable way of knowing the status of your battery than simply checking battery voltage, as voltage tends to temporarily drop during power punch-outs. This XT30 PCB can be used as replacement on the Diatone GT-R90, but also on other self build mini quads with this type of battery connector.
Brand: 
Category: 
Collection: 
Piezo Buzzer & Lost Model Alarm for Skyline32 / Nighthawk Pro 280 / SPRacingF3

5V Piezo Buzzer Lost Model Alarm for Racing Drones

£4.50

We've all seen the YouTube videos where a multirotor crashes into a field of long crop, never to be seen again. Well this little 5volt Piezo buzzer could be the savior; think of it like a SOS beacon for your drone. It’s super loud and will help guide you right to your aircraft.

It's compatible with lots of drone flight controlls including boards like the SPRacingF3 FC. It's also compatible with drones such as the Nighthawk Pro 280 and Diatone Crusader GT2.

Collection: 
Brand: 
Barcode: 
7109111462097
Subscribe to RSS - Diatone