FlyingTech.co.uk Site Logo

 

 

Specialist in Multirotor Tech & FPV Equipment

Mini Quad PDB with 12V Voltage Regulator

Matek Mini Quad PDB with 12V Linear Regulator for FPV Cam

£4.00

Here we have a mini power distribution board (PDB), which is ideal for micro quads, 200 to 180 size. The board itself provides four ESCs output connections, two unregulated auxiliary power output connections and a single 12v regulated connection, which is ideal for powering a 12v FPV camera. It uses a linear regulator which is better than a switching type regulator for FPV applications, as it reduces output voltage ripple and does not emit radio frequency interference, like switching regulators sometimes do.

Collection: 
Brand: 
Barcode: 
7109117045164
Tarot Octocopter Power Distribution Board Signal Hub - TL8X018

Tarot Octo Power Distribution Board Signal Hub - TL8X018

£54.90
If you've built a multirotor before you'll appreciate that there is a lot of wiring involved and it can be hard to keep all of it neat and tidy. This board has been designed to simplify the wiring and help keep it organised. It takes care of both power distribution and ESC signal wiring all in one neat package. The board is designed for octocopters so it features eight ESC signal inputs labeled M1 to M8. The connections are outputted together respectively at the signal hub, ready for you to connect with your flight controller*. On the power distribution side of things, the board has eight coaxial power ports to power your ESC’s and a couple of XT30 connectors to power auxiliary devices like UBECs and FPV gear. The board comes completes with a full wiring harness. It comes with eight coaxial power cables and eight signal wires, ready for you to solder to your ESC's and then plug straight into the board. The cables are long; 66cm and 42cm respectively, so they have enough length if you prefer to mount your ESC’s under the motors away from the main frame. The package also comes with high current 10AWG power leads soldered to a 7mm gold plated Amass AS150 anti-spark battery connector. Finally, a foam adhesive pad is included which should be stuck to the back of the board to insulate it from your frame. *Important: The signal hub does not have a positive connection, only signal and ground connections.
Brand: 
Collection: 
Barcode: 
7109114509140
Tarot Hexacopter Power Distribution Board Signal Hub - TL6X002

Tarot Hex Power Distribution Board Signal Hub - TL6X002

£37.50
If you've built a multirotor before you'll appreciate that there is a lot of wiring involved and it can be hard to keep all of it neat and tidy. This board has been designed to simplify the wiring and help keep it organised. It takes care of both power distribution and ESC signal wiring all in one neat package. The board is designed for hexacopters so it features six ESC signal inputs labeled M1 to M6. The connections are outputted together respectively at the signal hub, ready for you to connect with your flight controller*. On the power distribution side of things, the board has six coaxial power ports to power your ESC’s and a couple of XT30 connectors to power auxiliary devices like UBECs and FPV gear. The board comes completes with a full wiring harness. It comes with six coaxial power cables and six signal wires, ready for you to solder to your ESC's and then plug straight into the board. The cables are long; 66cm and 42cm respectively, so they have enough length if you prefer to mount your ESC’s under the motors away from the main frame. The package also comes with high current 10AWG power leads soldered to a 7mm gold plated Amass AS150 anti-spark battery connector. Finally, a foam adhesive pad is included which should be stuck to the back of the board to insulate it from your frame. *Important: The signal hub does not have a positive connection, only signal and ground connections.
Brand: 
Collection: 
Barcode: 
7109117271792
Tarot Quad Power Distribution Board Signal Hub TL4X004

Tarot Quad Power Distribution Board Signal Hub - TL4X004

£18.50

If you've built a multirotor before you'll appreciate that there is a lot of wiring involved and it can be hard to keep all of it neat and tidy. This board has been designed to simplify the wiring and help keep it organised. It takes care of both power distribution and ESC signal wiring all in one neat package. 

Collection: 
Brand: 
Barcode: 
7109117445711
XT90 Y lead Parallel Battery Harness Female to 2x Male

XT90 Y lead Parallel Battery Harness - 2x Male to 1x Female

£9.50
This XT90 2x male to 1x female battery harness can be used to connect two battery packs in parallel, for increased flight time and battery redundancy. For example, using it you can make 2 x 2200mAh 11.1v 3S1P packs into a single 4400mAh 11.1v pack 3S2. The cable is 10cm long and made of high quality silicone wire.
Collection: 
Barcode: 
7109111044965
XT30 to 4 X 2mm Female Bullet ESC Power Breakout Cable - ideal for 250 Racing Quads

XT30 ESC (2mm) Quadcopter Power Breakout Cable with JST

£7.00
This quadcopter power breakout cable simplifies your wiring harness by allowing you to easily plug everything together without soldering. The cable has four pairs of 2mm female gold bullet connectors to plug your ESCs into and an XT30 male plug to connect your flight battery to. There is also a JST male connector which is perfect for supplying power to peripheral accessories, for example a video transmitter, camera or LED lights etc (please check the working voltage in advance). If you are using the KK2.1.5 flight controller you can even plug the JST into its input voltage sensor to monitor battery life. The small size of this wiring harness lends itself to 250 style racing quadcopters, which is helpful as 250 drones tend to be crashed a lot. With the breakout cable being plug and play, you can replace motors and speed controllers quickly, without having to go back to your workshop. The wiring is high quality silicone insulated 16 AWG - splitting into 20 AWG.
Collection: 
Barcode: 
7109117695147
XT60 to 4 X 3.5mm Female Bullet ESC Power Breakout Cable with Male JST Plug

XT60 ESC (3.5mm) Quad / Hexa Power Breakout Cable with JST

£8.50

This power breakout cable simplifies your wiring harness by allowing you to easily plug everything together without soldering. The cable has pairs of 3.5mm female gold bullet connectors to plug your ESCs into and an XT60 male plug to connect your flight battery to. There is also a JST male connector which is perfect for supplying power to peripheral accessories, for example a video transmitter, brushless gimbal or LED lights etc (please check the working voltage in advance).

Collection: 
Barcode: 
7109112402863
Tarot 8 in 1 Power Distribution Board Hub - TL2909

Tarot 8 in 1 Power Distribution Board Hub - TL2909

£8.45
Most power distribution boards are exposed PCBs, which is ok, but they can look a little messy and there is the risk of shorting. This PDB from Tarot comes contained within a protective plastic shell. It's an 8-channel board, so you can use it to supply power to up to 8 ESCs. It features pre-tinned contacts that make soldering your ESCs and battery power leads to the board quick and easy.
Brand: 
Collection: 
Barcode: 
7109117984708
Power Distribution Board and Dual UBEC

DIY Octo Power Distribution Board and Dual UBEC

£17.90
This power distribution board (PDB) is a 3-in-1 device that simplifies even the most complicated multirotor builds. The PDB has two built in UBEC’s; one set at 5 volts, handy for a flight controller or receiver and the other adjustable from 10-20 volts, perfect for powering lighting, servos and other gear. The board even features integrated LED’s that illuminate when you plug a battery in. With this board, even if you’re building an octocopter you won't be stuck for connections. There are 12 positive/negative pads (8 large, 4 small) for power distribution and also four outputs for each UBEC. Best still, unlike many inferior boards this PDB can handle high Amps thanks to its 4oz copper construction, up to 120A to be precise. The UBEC's are just as impressive being rated for 5S high voltage setups. Finally when it comes to mounting the board, the standard M3 45mm spaced holes make it easy to mount to most multirotor frames. Please note that basic soldering skills are required to construct this board - see the assembly instructions for further information and the required equipment.
Brand: 
Collection: 
Barcode: 
7109111001074

Pages

Subscribe to RSS - Power Distribution