FlyingTech.co.uk Site Logo

 

 

Specialist in Multirotor Tech & FPV Equipment


COVID-19 Update: Flying Tech is open and shipping daily, however our phone support is limited so please email us if possible. Please note shipment times may take longer than normal as postal services are operating with fewer staff.

Thanks to all of our customers for their support at this difficult time and stay safe.

Color: 
#A8A8A8
TBS 1.2GHz VRX Notch Filter (868/915 MHz)

Title

TBS 1.2GHz VRX Notch Filter (868/915 MHz)

£14.50
Getting fuzzy video on your 1.2-1.3GHz receiver when using crossfire? This filter improves video reception for 1.2-1.3GHz video receivers in combination with TBS Crossfire. Due to the poor filtering on the video antenna input and wide operation frequency of most common 1.2-1.3GHz video receivers, they are unable to properly separate the video feed from the TBS CROSSFIRE transmission signal.  Mount this filter between your video receiver and antenna and you're good to go. This filter helps to block 868MHz and 915MHZ signals.  DESIGNED BY IBCRAZY
Brand: 
Category: 
Matek 1G3 VRX V2

Title

Matek 1G3 VRX V2 Long Range 1.2GHz - 1.3GHz Video Receiver

£44.50
This is the Version 2 - which is equipped with a Ground Station Dock PCB.  This is a 9CH 1.2GHz - 1.3GHz Long Range Video Receiver from Matek. It's designed to match their 1G3 Video Transmitter. The neat thing about this video receiver is that it fits a Fat Shark module bay, so you can install it in compatible FPV goggles or ground station docks. The module comes complete with a PCB antenna. FrSky R9 / TBS Crossfire Users - these radio control systems can interference with the Matek 1G3 video link as they operate on adjoining frequencies. To help reduce interference we recommend fitting a notch filter or using a 5.8Ghz relay station so that the 1G3 VRX can be positioned away from your radio control. Settings Press and hold the button 2 seconds to enter the frequency setting. Frequency LED blinks Press the button to select the frequency When the LED blinks at new frequency, no RF input is enabled on this frequency New frequency will be saved if no button action within 3 seconds
Brand: 
Category: 
Matek 1G3 Long Range 1.2GHz - 1.3GHz 600mw Transmitter

Title

Matek 1G3 Long Range 1.2GHz - 1.3GHz 600mw Transmitter

£37.99
This video transmitter from Matek is designed for super long range FPV. It operates on 1.2-1.3Ghz, which provides much better signal penetration through obstacles and long-range reception than 5.8Ghz. The VTX has a fixed 600mW power output and a single band with 9 channels. A compatible Matek video receiver for the 1G3-VTX is sold here. IMPORTANT: The use and operation of this product in your country may require an amateur radio license, and some countries may forbid its use entirely (It is NOT Legal in the UK). It is the responsibility of the purchaser to ensure that the purchase and use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Flying Tech Ltd cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. FrSky R9 / TBS Crossfire Users - these radio control systems can interference with the Matek 1G3 video link as they operate on adjoining frequencies. To help reduce interference we recommend fitting a notch filter or using a 5.8Ghz relay station so that the 1G3 VRX can be positioned away from your radio control. Settings Press and hold the button 2 seconds to enter the frequency setting. Frequency LED blinks Press the button to select the frequency When the LED blinks at new frequency, no RF output on this frequency New frequency and output will be enabled if no button action within 3 seconds *** CMS control is not supported for now *** This is the International 9HC Version. The 2CH US version is locked to 1258 & 1280MHz and cannot be unlocked to 9CH.
Brand: 
Category: 
Arkbird 5.8GHz Mini Auto Antenna Tracker (AAT)

Title

Arkbird 5.8GHz Mini Auto Antenna Tracker (AAT)

£199.00
An auto antenna tracker is a must for long distance FPV/Video operation and ensures the maximum reception at all times by tracking the model as it flies in all directions and altitudes.  The Arkbird AAT greatly improves the transmission range by pointing a high gain directional panel antenna at your model wherever it goes. This allows you to greatly increase your range without having to ever aim your antenna. It does that for you! The tracker works by using an airborne module on your model, which embeds GPS coordinates information into the transmitted FPV video signal. This is then received and decoded by the ground station to determine the azimuth (heading) and then direct the antennas beam to ensure it remains locked onto your model. The great thing about using an antenna tracker is that you can operate a FPV transmitter at legal power levels and still get good range. While it's possible to get FPV video reception over several 100 meters when using an omni-directional antenna at 25mW, you could expect to increase this to several kilometers by using a high gain directional antenna. This is the mini version for the Arkbird Auto Antenna Tracker. Aside from size, the most notable difference between the units is that the Mini ATT incorporates it's own 5.8GHz FPV receiver, where as with the full size ATT you have to provide a video receiver. Hence if you are using a frequency other than 5.8GHz or wish to use your own 5.8GHz Rx then use the full size ATT and not the Mini. The inetgrated Rx found in the Mini ATT makes the setup even easier as you only need to provide power (12V / 3S) and output the video to your screen or goggles using the cable provided. The airborne module is exactly the same and requires a GPS to work. If you are using one of the Arkbird GPS Autopilots you can share its GPS module with the AAT Airborne Module. If you aren't using one of the Arkbird autopilots you can purchase a plug and play M8N GPS module for it here. Prior your first flight or change of flying site, it is important to calibrate the tracker to ensure it is pointing directly at your model. To begin with do a short-range test flight and make sure the antenna is tracking your directly model. If the tracking is off, land and recalibrate the tracker. We recommend mounting the Mini ATT to the back of your monitor using some Dual Lock SJ3551 Tape. Beware that the ground station has a built in magnetometer so keep it away from sources of magnetic interference. Features: Inbuilt 40CH 5.8GHz FPV Receiver, works with 5.8GHz FPV systems Includes 12dBi Directional Antenna (RP-SMA) Greatly improves long distance transmission Plug and play setup Very compact, super portable Dynamic positioning can be achieved with additional GPS module USB interface for upgrades FAQs: Does the Arkbird Mini AAT System only work with 5.8GHz Video Systems? Yes, the Arkbird Mini ATT will only work with 5.8GHz analogue video frequencies a it has a built in 5.8GHz video receiver. Can I use another Antenna? Yes, you can change to a different 5.8GHz antenna (RP-SMA), although we have found that the stock 12 dBi delivers good performance. Does the GPS information affect the video? No, it's invisible and the ground station decodes this information. Does the ATT require an Arkbird Autopilot to work? No, the ATT system just requires a GPS module connected to the Airborne Module, although you can use it with the Arkbird Autopilots. Does it work with any FPV camera? It must be used with an analogue FPV camera that is PAL (not NTSC). Please note - the AAT ground station has a built in magnetometer so keep it away from sources of magnetic interference. Required: FPV system: Camera, Video Transmitter, Antennas - Omni-Directional for Model / High Gain Directional for Ground Station GPS Module for ATT Airborne system / or shared GPS module with Arkbird Autopilot 2.0. 12V Power Supply or 3S LiPo Optional: Arkbird AAT Airborne Module - the ATT Ground Station includes one airborne module. If you want to equip another FPV model with support for antenna tracking you can purchase an additional air module. Additional GPS Module - the ATT Ground Station can fix its home location from the GPS module connected to the airborne module, however if you wish to move the antenna tracker when in use, you'll need to connect to it a GPS module so that it knows its live home position.
Brand: 
Category: 
FPV Antenna Tracker Ground Station

Title

Arkbird AAT Auto Antenna Tracker FPV Ground Station

£285.00
An auto antenna tracker is a must for long distance FPV/Video operation and ensures the maximum reception at all times by tracking the model as it flies in all directions and altitudes.  The Arkbird AAT greatly improves the transmission range by pointing a high gain directional panel antenna (not supplied) at your model wherever it goes. This allows you to greatly increase your range without having to ever aim your antenna. It does that for you! The tracker works by using an airborne module on your model, which embeds GPS coordinates information into the transmitted FPV video signal. This is then received and decoded by the ground station to determine the azimuth (heading) and then direct the antennas beam to ensure it remains locked onto your model. The great thing about using an antenna tracker is that you can operate a FPV transmitter at legal power levels and still get good range. While it's possible to get FPV video reception over several 100 meters when using an omni-directional antenna at 25mW, you could expect to increase this to several kilometers by using a high gain directional antenna. The tracker has 2 sets of sensors for dual-coupling correction and is equipped with a magnetic compass and inertial navigation compass (gyroscope) for high precision tracking. Take off point coordinates can be automatically saved after powering up, and dynamic positioning is achieved by connecting a further GPS model (available separately) with the Ground Station. This is very handy if the antenna tracker is used on a moving vehicle or in the event of an emergency landing or searching for a lost model. The ATT system is easy to setup. The Ground Station tracker uses plug and play cabling to connect with your FPV receiver (not provided) and simply requires a 12V (3S) power input. The ATT airborne module requires a GPS to work. If you are using one of the Arkbird GPS Autopilots you can share its GPS module with the AAT Airborne Module. If you aren't using one of the Arkbird autopilots you can purchase a plug and play M8N GPS module for it here. Prior your first flight or change of flying site, it is important to calibrate the tracker to ensure it is pointing directly at your model. To begin with do a short-range test flight and make sure the antenna is tracking your directly model. If the tracking is off, land and recalibrate the tracker. The ground unit is supplied with integrated suction cups for mounting on a car roof etc and a tripod mounting so that you can choose which way you mount the tracker whilst its in use. Features: Plug and play when used with Arkbird Autopilot 2.0 Greatly improves long distance transmission 2 sets of sensors for dual-coupling correction High quality powerful steering motor with 360° slip ring Advanced fully automatic calibration algorithm for one step calibration Dynamic positioning can be achieved with additional GPS module Dual mounting, suction cup or tripod USB interface for upgrades AAT Usage: Power up FPV VTX / airside module (LED flashing quickly). Power up FPV VRX and tune into VTX frequency. Power up ground station and check for flashing lights (Red / Yellow) which indicate a GPS lock and decoded video feed. Position airborne module near ground station and press HOME button for 5 seconds to store GPS home location (If you have a GPS module connected to the ground module you can skip this step). Press CALIBRATE (CAL) button for 5 seconds to perfrom compass calibration. Confirm heading direction is pointing North and if use button one and three to adjust if required. Press CAL four times to confirm setup and exit. Fly FAQs: Does the Arkbird AAT System only work with 5.8GHz Video Systems? The full size Arkbird ATT will work with all analogue video frequencies. It requires the user to supply their own video receiver. Does the GPS information affect the video? No, it's invisible and the ground station decodes this information. Does the ATT require an Arkbird Autopilot to work? No, the ATT system just requires a GPS module connected to the Airborne Module, although you can use it with the Arkbird Autopilots. Does it work with any FPV camera? It must be used with an analogue FPV camera that is PAL (not NTSC). Please note - the AAT ground station has a built in magnetometer so keep it away from sources of magnetic interference. Required: FPV system: Camera, Video Transmitter, Video Receiver, Antennas - Omni-Directional for Model / High Gain Directional for Ground Station GPS Module for ATT Airborne system / or shared GPS module with Arkbird Autopilot 2.0. 12V Power Supply or 3S LiPo Optional: Arkbird AAT Airborne Module - the ATT Ground Station includes one airborne module. If you want to equip another FPV model with support for antenna tracking you can purchase an additional air module. Additional GPS Module - the ATT Ground Station can fix its home location from the GPS module connected to the airborne module, however if you wish to move the antenna tracker when in use, you'll need to connect to it a GPS module so that it knows its live home position.
Brand: 
Category: 
Arkbird-AAT Auto Antenna Tracker System Airborne Module

Title

Arkbird AAT Airborne Module

£44.99
This is the ATT Airborne Module that is used in conjunction with the Arkbird Auto Antenna Tracking Ground Stations, either the full size ATT Ground Station or the Arkbird Mini ATT Ground Station. The job of the Airborne Module is to embed GPS co-ordinate information into the video signal of your FPV system, which can then be received and decoded by the ATT Ground Station to enable it to track your model through the sky.  Both ATT systems ship with an ATT airborne module, so you only need to purchase this module if you want to equip another FPV model with support for antenna tracking. The ATT requires GPS to work. If you are using one of the Arkbird GPS Autopilots you can share its GPS module with the AAT Airborne Module*. If you aren't using one of the Arkbird autopilots you can purchase a plug and play M8N GPS module for it here. *Please note that the Arkbird Autopilot 2.0 has an inbuilt AAT Airborne Module so you don't need to use a separate Airborne Mdule in models that use that autopilot. FAQs: Does the Arkbird AAT System only work with 5.8GHz Video Systems? The Arkbird Mini ATT is only compatible with 5.8GHz as it uses a built in 5.8GHz receiver. The full size Arkbird ATT will work with all analogue video frequencies, as it requires the user to supply their own video receiver. Does the GPS information affect the video? No, it's invisible and the ground station decodes this information. Does the ATT require an Arkbird Autopilot to work? No, the ATT system just requires a GPS module connected to the Airborne Module, although you can use it with the Arkbird Autopilots. Does it work with any FPV camera? It must be used with an analogue FPV camera that is PAL (not NTSC).
Brand: 
Category: 
Menace Numskull 2.4Ghz Long Range FPV Patch Antenna SMA

Title

Menace Numskull 2.4Ghz Long Range FPV Patch Antenna SMA

£19.99
The MenaceRC Numskull Antenna is perfect for the latest 2.4Ghz goggle modules and at home on a base station singularly or as part of a diversity receiving module. Whether you are planning on using 2.4Ghz on a Wing or a Drone, the Numskull’s performance will ensure you are getting the optimum video signal at close quarters as well at long range with a real world range in excess of 17.5 km!
Brand: 
Category: 
TBS Long Range 2.4GHz YAGI (11dB) FPV Antenna

Title

Team BlackSheep 2.4GHz YAGI (11dB) FPV Antenna

£43.99
The TBS Yagi is a highly versatile all-round 2.4GHz antenna offering ranges of between 7 and 15km when used with the TBS 2.4GHz video transmission system. Lightweight, compact and mobile, its long, slim shape is perfect for mounting on a tripod. The Yagi is hand-made by a german engineer with fine attention to detail. The build finish is exceptional and the resulting link and video quality is nothing short of phenomenal. You will notice a sharper, higher contrast picture compared to most antennas. This is Trappy's antenna of choice.
Brand: 
Category: 
Barcode: 
7109113166597
800mW TBS Unify 2.4GHz 16ch Video Transmitter

Title

Team BlackSheep Unify 2G4 500mW / 800mW 16CH VTX

£99.00
The latest and greatest 2G4 video transmitter from the leaders in long range technology. A successor to the widely popular TBS Tuned Lawmate 2G4 VTx with 16ch, and a choice of 500mW and 800mW of output power.  We are proud to announce a new line of video transmitters, optimized for long range and small form factor, completely redesigned and tailored for FPV use. Perfect for small multi rotor platforms or in applications where flight times are critical. It obviously works on big platforms too! We've taken this to 40km and back in prototype phase, with a regular TBS Yagi you can expect up to 15km of flyable video. The transmitter is protected by a rugged aluminum case that also acts as heat sink, making it extremely reliable, robust and crash-friendly. The sexy design rounds off an otherwise already perfect product. When everyone was jumping to 5G8, TBS has stayed loyal to 2G4 video technology and has been flying it all around the globe, pushing this frequency to its limits and beyond. All this experience was distilled into the design of the video transmitter.  Want to fly between trees? Then fly out long distance a few feet off the deck? How about a proximity run down a steep alpine slope, in and out of LOS? That's what we do for entertainment, this is why we wanted to make a better, more affordable video transmitter. And here it is! Download manual COMPATIBILITY The TBS UNIFY line of video transmitters strives for maximum compatibility among the slew of different frequencies. If TBS Unify is on it, we've tested it with the most common receivers and we've strived for compatibility with whatever receiver you may have lying around. The TBS 2G4 VTx, like our other transmitters, works plug and play with the CORE, CORE PNP25, CORE PNP50 or CORE PRO. It also integrates seamlessly with a variety of third party OSD's and power supplies.  This video transmitter operates on frequencies outside of the band of regular R/C video transmitters. You can therefore fly together with mates on 2G4 R/C. A few meters of clearance is enough for uninterrupted video signal, even when flying long range.  CUSTOMIZE IT! If you're into customization, this video transmitter is also for you! You can pop the PCB out of the case, solder on a tin shield and save yet another few grams and a few millimeters off the edges. We're into multirotors just like you, and we know the difference this can make! There are also another 16 undocumented frequencies alloted. If you're the sort of guy that loves to hack into your receivers, you can pick out of 16 totally unsupported frequencies, ensuring that you can be the guy flying at all times, even on the biggest meetups. Features Tiny form factor  Exceptional Range Excellent video clarity Low power consumption at 5V input  Full aluminum enclosure for heat dissipation and protection  ​Note: Please check with your local authorities regarding operation of this equipment before you purchase. Regulations on power output, usable frequencies and licences to operate vary from region to region.
Brand: 
Category: 
Barcode: 
7109112116975

Pages

Subscribe to RSS - Long Range FPV