FlyingTech.co.uk Site Logo

 

 

Specialist in Multirotor Tech & FPV Equipment

Matek UBEC DUO with Aux Control

Matek UBEC DUO Dual Outputs 4A 5V & 5~12V with Aux Control​

£17.99

We sell a lot of different voltage regulators on Flying Tech, but the Matek UBEC DUO is the one that stands out from them all, simply because it does most things and of course being made by Matek you know it will be reliable.

It provides voltage regulation, noise filtering, voltage monitoring and a RC power on / off function.

Collection: 
Brand: 
Matek PDB-XPW PDB with 140A Current Sensor, Dual BEC, XT60

Matek PDB-XPW PDB with 140A Current Sensor, Dual BEC, XT60

£9.90

The Matek PDB-XPW is a power distribution board with punch and is designed for X frames. It will take input from 3S to 5S Lipo batteries which are ideal for racing drones. Power is provided to four ESCs and it is regulated and synchronized 5V DC and linear regulated 12V DC for all your gear such as Flight Controllers, cameras, video transmitters, RC receivers, LEDs, etc.

Collection: 
Brand: 
Barcode: 
7109112724200
MATEK HUBOSD ECO STOSD8 OSD & PDB X-TYPE WITH XT060

Matek HUBOSD ECO X PDB with Current Sensor, Dual BEC, XT60

£16.90

The Matek HUBOSD eco X-Type PCB is a multifunctional HUB with 4 channel PDB, dual BECs, a current sensor and a plug and play integrated OSD.

The PDB can provide power up to four ESCs rated at 30A per channel and compatible with 3 to 5S LiPo batteries. The BEC outputs provide 5volts at 2A and 12volts at 0.5A. The 5V BEC connection is ideal for powering your flight controller or RC receiver. The 12v BEC is a linear type regulator so no LC filter is needed to clean up the power supply if used for a 12V FPV camera. 

Collection: 
Brand: 
Barcode: 
7109111374406
Matek Systems HUBOSD8-SE w/STOSD8-SE, Current Sensor, Dual BEC and 6S Max

Matek HUBOSD8-SE 9-27V PDB with Current Sensor & Dual BEC

£17.99

The Matek HUBOSD8-SE is a fully featured well designed PDB for FPV racing drones. It is a multifunctional HUB with 4 channel PDB, dual BECs, a current sensor and a plug and play integrated OSD.

The PDB can provide power up to four ESCs rated at 30A per channel and compatible with 3 to 6S LiPo batteries. The BEC outputs provide 5volts at 1.5A and 10volts at 1.5A, while the built-in current sensor measures up to 184A. Note that the 10V output can be used to power 12V cameras.

Collection: 
Brand: 
Barcode: 
7109119989565
Matek 5V Piezo Buzzer Lost Model Alarm Compatible with FC or PWM

5V Piezo Buzzer Lost Model Alarm (PWM / FC Compatible)

£4.50

Here's another 5V piezo buzzer, but this one is different from the rest in that it's compatible with both PWM receivers and with most racing drone flight controllers. When used with a flight controller, it can be setup as a low voltage alarm, lost model alarm and it can also be configured to provide status alerts like 'no rx signal' and other warnings*. If you use it with a traditional PWM receiver, simply connect it an auxiliary channel and activate it with a switch on your transmitter.

Collection: 
Brand: 
Barcode: 
7109113653172
Matek 3 in 1 Battery Monitor, Signal Loss Alarm & Discovery Buzzer

3 in 1 Battery Monitor, Signal Loss Alarm & Discovery Buzzer

£7.99

The Matek 3-In-1 Battery Monitor, Signal Loss and Lost Airplane Alarm is a handy little device that will help protect your valuable investment. First, it acts as a battery voltage monitor. Once voltage gets below the threshold you set, the alarms will go off and a red LED will illuminate. Additionally it can detect if signal is lost to your receiver, and just like the voltage monitoring feature, the alarms will go off. The last feature is the lost model alarm which operates when plugged into an auxiliary channel on your receiver, such as the retract switch.

Collection: 
Brand: 
Barcode: 
7109113146322

Pages

Subscribe to RSS - Mateksys