Site Logo



Specialist in Multirotor Tech & FPV Equipment

Matek 5.8G VTX-HV Switchable Video Transmitter with BFCMS Control (MMCX Antenna)


Matek 5.8G VTX-HV Switchable Video Transmitter with BFCMS

MATEK VIDEO TRANSMITTER 5.8G VTX-HV W/ BFCMS CONTROL 40CH, 25/200/500mw switchable, 6~27V Input, Traditional button+LED control, BFCMS control via FC Uart_TX, Stack mounting. Matek make some of the best racing drone flight controllers and now they are expanding their product range with this video transmitter. The Matek VTX-HV is excellent value for money and is the perfect partner to their F405 OSD / AOI Flight Controller as it stacks on top to give you a fully functional FPV racing stack. The unit has 40 standard channels and is switchable between 25, 200 and 500mW. Best still, the VTX connects directly to Betaflight allowing you to configure the VTX power and channel via your radio and an OSD menu. The Matek VTX includes a lightweight UFL / MMCX (select as required) pigtail connector and also an SMA connector for regular FPV antennas. The unit supports a wide input voltage from 2 to 6S (7~27V) and has a 5V/1A BEC output to power a camera or the FC. It also utilizes the standard 30.5mm mountings, which allows it to stack with other units on the market. Frequency Table: Boscam A (A) 5865/5845/5825/5805/5785/5765/5745/5725 Boscam B (B) 5733/5752/5771/5790/5809/5828/5847/5866 Boscam E (E) 5705/5685/5665/5645/5885/5905/5925/5945 Fatshark    (F) 5740/5760/5780/5800/5820/5840/5860/5880 Raceband (R) 5658/5695/5732/5769/5806/5843/5880/5917 Features: Connects directly to Betaflight letting you configure VTX power and channel via your radio at the field via OSD menus Wide input voltage (7~27V) 40 standard channels Output power is switchable (25, 200 and 500mW) 5V/1A BEC output or Camera or FC Traditional button and LED control BFOSD and LUA Script compatible Firmware upgradeable Stackable with standard 30.5mm mounts
Matek Vibration Dampening Flight Controller FC Standoffs

Matek Vibration Dampening Flight Controller FC Standoffs

The latest F3 and F4 flight controllers are incredibly sensitive to vibration so soft mounting is essential; really, don't attempt a build without some sort of dampening as you will more than likely run into lots of issues ranging from mid throttle oscillation to yaw twitches. These high-quality rubber standoffs from Matek are the perfect solution, put them underneath the flight controller to isolate vibration generated by motor and propellers. They come with a male and female thread for easy installation and are compatible with most flight controllers. We sell both M3 and M2 sets; regular drone flight controllers typically use M3 and M2 used for micro FCs. We sell a full racing drone FC / PDB soft mount kit which includes the Matek Anti Vibration Spacers and m3 nylon fittings here.
Matek FCHUB-6S PDB for F405 FC, 184A Current Sensor & Dual BEC

Matek FCHUB-6S PDB for F405 Flight Controller w/ 5V 10V BECs


Matek has created another superb Power Distribution Board (PDB) capable of utilising 3 to 6S lipo batteries. It will provide 120A current to four ESCs (30A each ESC). As well as this it provides regulated and filtered 5V DC (1.5A) and 10V DC (1.5A) outputs for powering items such as cameras, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc.

Matek Step Up Voltage Regulator Adjustable Output 3-13V to 5-15V

Matek Step Up Voltage Booster Input 3-13V / Output 5-15V (3A)


The Matek step-up voltage booster module can generate high output voltages from input voltages as low as 3V. It uses a high-efficiency DC-DC voltage regulator to increase the supplied input voltage. The output voltage can be adjusted from 5-15V via the potentiometer. The available output current is a function of the input voltage, output voltage, and efficiency - for these values make reference to the Typical Efficiency and Output Current Table found in the Manual.



Subscribe to RSS - Mateksys